1/2 www.rohm.com c 2009 rohm co., ltd. all rights reserved. 2009.05 - rev.c (1) gnd (2) in (3) out rohm : smt3 eiaj : sc-59 dtd123yk abbriviated symbol : f62 each lead has same dimensions ( 2 ) ( 1 ) 2.8 1.6 0.4 ( 3 ) 2.9 1.9 0.95 0.95 0.8 0.15 0.3min. 1.1 digital transistors (built-in resistors) dtd123yk z applications z dimensions (unit : mm) inverter, interface, driver z features 1) built-in bias resistors enable the configuration of an inverter circuit without connecting external input resistors see equivalent circuit). 2) the bias resistors consist of thin-film resistors with complete isolation to allow negative biasing of the input. they also 3) have the advantage of almost completely eliminating parasitic effects. 4) only the on / off conditions need to be set for operation, making the device design easy. z structure z inner circuit npn epitaxial planar silicon transistor (resistor built-in type) z package specifications smt3 dtd123yk part no. t146 3000 package packaging type code basic ordering unit (pieces) taping z absolute maximum ratings (ta=25 c) limits parameter symbol v cc 50 ? 5 to + 12 500 200 150 ? 55 to + 150 dtd123yk v v in v ma mw c c i c p d tj tstg unit supply voltage output current power dissipation junction temperature storage temperature input voltage r 1 r 2 in r 1 =2.2k ? , r 2 =10k ? gnd out in gnd out
2/2 www.rohm.com c 2009 rohm co., ltd. all rights reserved. 2009.05 - rev.c data sheet dtd123yk z electrical characteristics (ta=25 c) ? parameter symbol v i(off) v i(on) v o(on) i i i o(off) r 1 g i r 2 /r 1 f t min. ? 2 ? ? ? 1.54 56 3.6 ? ? ? 0.1 ? ? 2.2 ? 4.5 200 0.3 ? 0.3 3.6 0.5 2.86 ? 5.5 ? v v cc = 5v, i o = 100 a v o = 0.3v, i o = 20ma i o /i i = 50ma/2.5ma v i = 5v v cc = 50v, v i = 0v v o = 5v, i o = 50ma v ce = 10v, i e = ? 50ma, f = 100mhz v ma a k ? ? ?? ? mhz typ. max. unit conditions ? characteristics of built-in transistor input voltage output voltage input current output current dc current gain input resistance resistance ratio transition frequency z electrical characteristics curves input voltage : v i(on) (v) output current : i o (a) v o = 0.3v 500 1m 2m 5m 10m 20m 50m100m 200m 500m 2 1 500m 200m 100m 100 50 20 10 5 fig.1 input voltage vs. output current (on characteristics) 25 c 100 c ta = ? 40 c input voltage : v i(off) (v) output current : io (a) v cc = 5v 0.5 1.0 1.5 2.0 2.5 3.0 0 10m 5m 2m 1m 500 200 100 50 20 10 5 1 2 fig.2 output current vs. input voltage (off characteristics) ta = 100 c 25 c ? 40 c v o = 5v output current : i o (a) dc current gain : g i 1k 500 200 100 50 20 10 5 2 1 1m 2m 5m 10m 20m 50m 500m 100m 200m 500 ta = 100 c 25 c ? 40 c fig.3 dc current gain vs. output current output current : i o (a) output voltage : v o(on) (v) fig.4 output voltage vs. output current l o /l i = 20 500 1m 2m 5m 10m 20m 50m 500m 100m 200m 1 500m 200m 100m 50m 20m 10m 5m 2m 1m 25 c ? 40 c ta = 100 c
r0039 a www.rohm.com ? 2009 rohm co., ltd. all rights reserved. notice rohm customer support system http://www.rohm.com/contact/ thank you for your accessing to rohm product informations. more detail product informations and catalogs are available, please contact us. notes no copying or reproduction of this document, in part or in whole, is permitted without the consent of rohm co.,ltd. the content specified herein is subject to change for improvement without notice. the content specified herein is for the purpose of introducing rohm's products (hereinafter "products"). if you wish to use any such product, please be sure to refer to the specifications, which can be obtained from rohm upon request. examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the products. the peripheral conditions must be taken into account when designing circuits for mass production. great care was taken in ensuring the accuracy of the information specified in this document. however, should you incur any damage arising from any inaccuracy or misprint of such information, rohm shall bear no responsibility for such damage. the technical information specified herein is intended only to show the typical functions of and examples of application circuits for the products. rohm does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by rohm and other parties. rohm shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. the products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, commu- nication devices, electronic appliances and amusement devices). the products specified in this document are not designed to be radiation tolerant. while rohm always makes efforts to enhance the quality and reliability of its products, a product may fail or malfunction for a variety of reasons. please be sure to implement in your equipment using the products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any product, such as derating, redundancy, fire control and fail-safe designs. rohm shall bear no responsibility whatsoever for your use of any product outside of the prescribed scope or not in accordance with the instruction manual. the products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). rohm shall bear no responsibility in any way for use of any of the products for the above special purposes. if a product is intended to be used for any such special purpose, please contact a rohm sales representative before purchasing. if you intend to export or ship overseas any product or technology specified herein that may be controlled under the foreign exchange and the foreign trade law, you will be required to obtain a license or permit under the law.
|
